What to consider when choosing a gate made of corrugated board with a wicket?
Living in a private house, for obvious reasons, each person wants not only to protect his site from strangers, but also to install a comfortable gate with a wicket on it. When choosing a suitable option, you should pay attention to the corrugated gates with a wicket, the popularity of which in Russia is due to the budgetary cost, as well as aesthetic beauty. The secret of the demand for professional flooring is that this material is the best fit for the gate. After all, it has such qualities as durability, relatively low weight and versatility of use.
A wide selection of standard sizes and colors of corrugated doors
In order for a metal swing gate with a wicket made of corrugated board to be strong and durable, it is important to consider the following:
- At the first stage, it is imperative to draw up a draft design, in which it is important to determine the dimensions of the structure, the type of material used and its amount, calculate the weight load, as well as the necessary accessories (hinges, handles, locks)
- The materials must be of high quality, and this applies not only to the corrugated board, which must be purchased from a trusted manufacturer, but also to the profiled rectangular or square pipe, from which the frame will be cooked. The same applies to fittings, which must be resistant to wear and tear, as well as the necessary additional elements: self-tapping screws, riveted "caps", bolts, stoppers and other
- One of the most difficult stages of work is the alignment of individual sections of the profile to obtain a regular rectangle, which is not easy to do due to its large size, so a locksmith corner is used here
- The doorway can be located not only on one side, but also closer to the middle, which depends solely on the wishes of the customer
- Taking into account the high load that the support pillars will experience, special attention should be paid to their appropriate cross-section, as well as competent concreting
It is important to understand that it is quite possible to make a wicket and gates from corrugated board with your own hands, but this will require a certain investment of time and effort.
When making a frame and sashes, welding of blanks is best done on a flat surface with minimal height differences, for which you can lay a sheet of iron or tin on the ground.
If a person doubts his capabilities, you can contact a specialized company that provides the appropriate services. By entrusting the design, construction and installation of experienced specialists, the customer gets confidence that a gate with a wicket will be produced in a short time, which will serve for many years.At the same time, the gates made of corrugated board with a wicket inside, the drawing of which is provided to the customer for approval, must be made of certified materials.
Options for doors made of corrugated board with a wicket
There are many types of such structures, due to the size and configuration, but in general, there are 3 most popular types:
- An attached structure, where a third is added to the two existing posts, on which the frame wicket is hung. This is the simplest version of the gate.
- Wicket built into the gate. This is a complicated option that requires careful calculations, but it wins in that it saves space, which is especially important when there is a shortage of it.
- Sliding corrugated board. This option is less common and more difficult to make.
Not all types are used as facing material corrugated board, but only grades "N", "C" and "NS" of wall type, the thickness of the metal is not less than 0.5 mm. When choosing a suitable gate made of corrugated board with a wicket, it is important to check that the corrugated board has a high-quality polymer coating, and is also made of galvanized metal. This will avoid the destructive process of corrosion and maximize the operational life of the structure. As an additional decoration, the supporting pillars can be overlaid with decorative masonry made of red facing bricks.
Numerous photos of corrugated gates with a wicket, presented on the Internet, help the owners quickly decide which option suits them best. The gates with additional decoration with forged elements look especially attractive, due to which it is possible to give the design uniqueness and "richness".
If the structure is not made of new metal, but a used pipe, it must be treated with a rust converter, after which it should be primed and painted.
When planning to place an order for the manufacture of a gate from a corrugated board with a wicket, it is better to contact the company that can also carry out the delivery and installation of the turnkey structure. This is very convenient, since it saves a person from the need to separately look for a team of professional installers. In order to be sure that the gate will be made with high quality, it is best to conclude a written agreement with the company, which will reflect the rights and obligations of the parties.